Σελίδες:
  • #1 από the bard στις 07 Feb 2008
  • Ξερει κανεις ποσο περιπου πρεπει να χαλαρωσω το truss rod αφου ξακουρδισω απο d standard σε c# standard?Προσφατα εκανα setup σε ρε απο μι, αλλα σκεφτομαι να την ξεκουρδισω αλλο λιγο....Δεν ειμαι διατεθειμενος να σκασω αλλο ενα 35αρι για σεταπ, αν μπορω να το κανω μονος μου.Υπηρχε ενα θεμα παλιοτερα που ελεγε ποσο στριβουμε τη βιδα κλπ αλλα δεν το βρισκω..Αν δηλαδη εχει καποιος τη εμπειρια να μου πει στο περιπου μην το παρακανω με το αλεν και σπασω κανενα μπρατσο  :o Η κιθαρα ειναι Jackson V με 11αρες χορδες
    Ευχαριστω :)
  • #2 από don spiretos στις 07 Feb 2008
  • Adjusting the neck relief

    A neck with a light bow leaves more room for the vibrations of
    the strings. Any adjustment made only applies for the set of
    strings that is fitted at the moment the truss rod is adjusted as it
    compensates exactly the pull exerted by a particular set of strings
    and keeps the neck bow within certain limits. Any later change of
    the string gauge also calls for a readjustment of the neck bow.
    However, before you embark on adjusting the neck relief, tune
    the guitar and then put it away and leave it to “work” overnight:
    the pull of the strings will take some time to become effective.
    Then retune the guitar and place a straight edge over the first 13
    frets, holding the guitar in the playing position. It is important to
    hold the guitar and not to have it lying flat on a surface as the
    weight of the neck alone would already lead to distortions in
    adjustment. If you place a capo on the first fret, you will have one
    hand free for checking the straightness with a feeler gauge (1). If
    you press down a string after the 12th fret, it is dead straight and
    can be used in place of a straight edge to check the straightness
    of the neck. The recommended distance (neck relief) between
    the top of the sixth fret and the bottom of the straight edge or
    string depends on the scale length and the string gauge. Shorter
    scale lengths and thinner strings produce less strong vibrations
    while long scales and bass strings require more room for vibrating.
    Guitars can have a relief of 0.25 to 0.3mm (0.01" - 0.013");
    0.5mm (0.02") is recommended for basses. The neck bow can be
    rough-adjusted by pressing down a string at the 1st and 13th fret
    and by tapping it with a finger at the 6th fret and then making any
    adjustment that may be necessary. Always loosen the strings
    before turning the truss rod nut. Adjust the truss rod so that the
    distance is right: turning the adjustment nut in a clockwise
    direction gives the neck a backbow and reduces this distance; if
    the distance between the strings and the frets is too small, the
    adjustment nut has to be untightened by turning it in an anticlockwise
    direction. Never turn the nut by more than a quarter of
    a turn at a time
    . After each truss rod adjustment the strings have
    to be retuned and the full pull of the strings has to be reestablished.
    The neck bow may change in the course of the other
    adjustments yet to be made and described below; it may therefore
    be necessary to carry out the above adjustment procedure
    several times. But once the guitar is completely set up and the
    neck relief is right no further adjustments are needed and the
    truss rod is best left untouched. The truss rod will only require
    readjusting when strings of a different gauge are fitted on the
    guitar. And finally: the truss rod must never be used for setting
    the action – its only purpose is to adjust neck relief.
  • #3 από the bard στις 07 Feb 2008
  • "...Never turn the nut by more than a quarter of a turn at a time..."
    Eδω ειναι το "ζουμι".Τhanx φιλε!

Σελίδες: